Atom cutting machine

ATOM have been producing cutting machine since 1946 .Now they have the following hydraulic cutting machine:

1.swing arm cutting machine

Atom produces four main types of swing beam cutting presses, these include:

SE Series (Entry Level)

atom-cutting-machine

This swing beam cutting press is extremely simple to use with easy adjustment of the cutting stroke, an operator can switch between multiple height cutting dies without any setting or adjustment.

The control push buttons are ergonomic, so allowing the operator increased comfort. The push buttons are controlled by a two hand safety relay, meaning the buttons need to be activated 5/10ths/sec between each other too allow cutting stroke activation, and requires constant activation to maintain a cut stroke.

The cutting power is easily adjusted if required through the movement of a simple potentiometer on the cutting beam.

A functional machine, constructed in the same way as other models, but even simpler to use. The basic machine, with automatic setting of stroke end, working with dies of different height is not a problem.

SE Series Model Cutting Table (mm) Arm Width (mm) Max. Cutting Power (ton/ kN) Max. Stroke (mm) Max. Daylight (No Board) (mm) Motor Power (HP/ kW) M/C Dimensions (mm) Net. Weight (No Oil) (Kg) Weight (Inc. Packaging) (Kg)
SE 8 600×300 300 8t/ 78 90 125 1HP / 0.75kW 600x690x1330 430 500
SE 20C 900×430 370 20t/ 196 900x870x1400 630 745
SE 20 900×450 370 22t/ 216 900x960x1425 880 1000
SE 22 1200×500 500 22t/ 216 1200x1030x1425 1060 1200
SE 24C 900×450 370 25t/ 245 900x960x1425 880 1000
SE 24 1000×500 370 25t/ 245 1000x1010x1425 990 1120
SE 25C 900×450 500 25t/ 245 900x960x1425 900 1020
SE 25 1000×500 500 25t/ 245 1000x1030x1425 1030 1160
SE 25L 1000×500 610 25t/ 245 1000x1030x1425 1050 1180

S100 Series

atom-cutting-machine-s100

This type of cutting press is equipped with three different cutting pressures to enable the use of different sized (surface area) dies without any repeating adjustments.

The S100 swing beam cutting press is like the SE Series simple to use with easy adjustment of the cutting stroke, an operator can switch between multiple height cutting dies without any setting or adjustment.

Unlike the SE swing beam the S100 has a 3 push button cutting power selection rack, this means that as an operator moves from a smaller die to a larger tool (surface area) rather then adjust the cutting power settings, any 1 of 3 buttons can be used on the left push button console to achieve an accurate cut.

The cutting power is easily adjusted if required through the movement of a two potentiometers on the cutting beam, the smaller of the two adjusts the 1st button of the 3 and the larger controls the 3rd push button. The 2nd push buttons cutting power is an average taken between the smaller and larger settings.

The control push buttons are ergonomic, so allowing the operator increased comfort. The push buttons are controlled by a two hand safety relay, meaning the buttons need to be activated 5/10ths/sec between each other too allow cutting stroke activation, and requires constant activation to maintain a cut stroke.

The specifications and models available within this range are listed below:

All S100 Series swing beam cutting presses are supplied with a CE Mark of conformity.

S100 Series Model Cutting Table (mm) Arm Width (mm) Max. Cutting Power (ton/ kN) Max. Stroke (mm) Max. Daylight (No Board) (mm) Motor Power (HP/ kW) M/C Dimensions (mm) Net. Weight (No Oil) (Kg) Weight (Inc. Packaging) (Kg)
S108 600×300 300 8t/ 78 90 125 1HP / 0.75kW 600x690x1330 430 500
S120C 900×430 370 20t/ 196 900x870x1400 630 745
S120 900×450 370 22t/ 216 900x960x1425 880 1000
S122 1200×500 500 22t/ 216 1200x1030x1425 1060 1200
S124C 900×450 370 25t/ 245 900x960x1425 880 1000
S124 1000×500 370 25t/ 245 1000x1010x1425 990 1120
S125C 900×450 500 25t/ 245 900x960x1425 900 1020
S125 1000×500 500 25t/ 245 1000x1030x1425 1030 1160
S125L 1000×500 610 25t/ 245 1000x1030x1425 1050 1180

‘Multiforce’ (light swing)

multiforce atom cutting machine

This system automatically adjusts the cutting pressure required to increase ease of use, reducing the wear on the cutting board(up to 50%) and maximising energy economy.

The ‘Multiforce’ differs from other swing beam cutting presses by operating to a stroke end system, therefore meaning it reaches the same depth each time. It also boasts the ‘light swing’ arm, which makes arm movement by the operator effortless.

The ‘Multiforce’ device allows a cutting board saving of up to 50%, so not only saving money, but also allowing better cutting across the board due to less wear, and so board reduced contours.

The ‘light swing’ arm can be supplied in a super light alloy, so yet again decreasing weight on the cutting beam, and so minimising operator effort required, and reducing fatigue.

Multiforce Model Cutting Table (mm) Arm Width (mm) Max. Cutting Power (ton/ kN) Max. Stroke (mm) Max. Daylight (No Board) (mm) Motor Power (HP/ kW) M/C Dimensions (mm) Net. Weight (No Oil) (Kg) Weight (Inc. Packaging) (Kg)
MF 20C 900×430 370 20t/ 196 90 125 1HP / 0.75kW 900x1000x1710 660 775
MF 9.1 900×450 370 22t/ 216 900x1090x1710 910 1030
MF 9.3S 900×450 370 25t/ 245 900x1090x1710 910 1030
MF 9.3 1000×500 370 25t/ 245 1000x1140x1710 1020 1150
MF 9.4 1000×500 500 25t/ 245 1000x1160x1710 1060 1190
MF 9.5 1000×500 610 25t/ 245 1000x1160x1710 1080 1210
MF 9.6 1200×500 610 22t/ 216 1200x1160x1710 1100 1230
MF 9.1A** 900×450 370 20t/ 196 900x1120x1710 910 1030
MF 9.4A** 1000×500 500 20t/ 196 1000x1130x1710 1060 1190

 

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s